Technical Specifications:
| Power Source |
AC 220 - 240V, DC 9V battery backup |
Alarm Volume |
>85dB(A) @ 3 meters. |
| AC Quiescent Current |
< 100mA |
Low Voltage Threshold |
<DC 7.6V |
| AC Alarm Current |
< 100mA |
Hush Time |
about 8minutes |
| DC Quiescent Current |
<10uA |
Product Service Life |
>10 year |
| DC Alarm Current |
< 28mA |
Humidity Range |
< 93% relative humidity (RH) |
| Heat Sensitivity |
54ºC-65ºC. |
Temperature Range |
0ºC~65ºC |
| Comply With Standard |
BS 5446-2:2003 |
Size |
140mm in diameter x 58.8mm depth |
| Sound Pattern |
ISO8201 (BI 0.5s - pause 0.5s - BI 0.5s - pause 0.5s - BI 0.5s - pause 1.5s, with the RED LED flash, repeat this alarm pattern) |
Details of the product function:
| Standby mode |
after the product is installed, if the heat alarm device operate properly, the red LED flashes once every 40 seconds |
| Local alarming mode |
when the heat alarm device detect the environmental temperature arrive the alarming condition, the red LED will flash once per second with pulsating alarm until thetemperature declined |
| Interconnection alarming mode |
when the heat alarm device detect the environmental temperature between 54ºC- 65ºC, the alarm will send local alarm signal, other interconnection alarms will send alarm signals. The wired interconnection alarms will go into interconnection alarming mode: BI - BI - pause 1.2s, with the red LED flashes, the alarm pattern is repeated |
| Low battery mode |
when the battery voltage below threshold, the red LED will flash once every 40 seconds with a sound of "chrip" |
| Fault mode |
if the alarm detection signal decays below threshold, the alarm chirp occurs without LED flashes every 40 seconds |
| Silence mode |
press the test button at least 2 seconds, it will go into silence mode for approx 8 minutes. That will desensitize the alarm sensitivity temporarily. At this time, the red LED will flash once every 8 seconds |
| No disturb mode |
when the alarm device is in low battery mode, in order to avoid disturbing you at night, please press the test button for 3 seconds which will mute this warning tone for about 14 hours. After 14 hours, the warning tone will still go off. The red LED will flash once every 40 seconds during NO DISTURB MODE |
| Test mode |
test the unit to ensure operate properly by pressing the test button. At this time, the red LED will flash once per second with pulsating alarm until test button is released |
| NOTE |
WEEKLY TESTING IS REQUIRED. |
Wireless Interconnection Set up
| >1< |
Select one of smoke alarms as the MASTER unit. Treat other units as SLAVE units. |
| >2< |
Press the test button on the MASTER unit three times within two seconds, the red LED will flash quickly, the unit is now in sending radio signal mode. This mode will last for 48 seconds. |
| >3< |
While the MASTER unit is in sending radio signal mode, press the test button on any SLAVE unit three times within two seconds, the SLAVE unit learns this signal and completes the pairing after a sound "beep" with light flash once. |
| >4< |
Repeat the above steps on all other SLAVE units. |
| Clear wireless connection function |
Press the test button on any SLAVE unit three times within two seconds, the red LED will flash quickly, then press and hold the test button again until the red light goes out the first time and release the button immediately, the red LED will flash slowly, at this time, press the test button again, the SLAVE unit will beep 3 times, which means that the SLAVE unit clears wireless connected successfully. |
| NOTE |
Only successfullyinterconnected units can clear the radio signal. Clearing the radio signal only removes the radio signal from the SLAVE unit. The MASTER unit cannot clear the radio signal. |
AC 220V main power DC 9V backup battery with wired and RF
interconnected heat alarm
Product description:
The unit is a heat alarm. It can rapidly detect incremental temperature and give off warning under the condition that the environmental temperature between 54ºC-65ºC, in order to alert the dwelling of the dangerous situation and notice residents to evacuate right away. In the alarming mode, if the alarm is connected with other heat detectors, other alarms will also send alarm signals.
It is operated by AC 220 - 240V/50 -60Hz with DC 9V battery backup and warns you when the battery is low.In order to not disturb your rest, the product designed function of silence and no disturb.
The heat alarm should be installed in kitchen, garage and other area of the home. Making sure the people at home will be able to hear and respond to the alarm sound. Installation position should be near possible fire source.
The test function of the product design is to test whether the product works properly by pressing the test button.Weekly testing is required.
This product is designed with interconnection function, it can realize interconnection alarm.
NOTE:NOT SUITABLE AS A FIRE SAFETY DEVICE UNLESS INTERCONNECTED TO ONE OR MORE SMOKE ALARMS.
){kind=link}