Mains Power Hardwired Interlinked AC Smoke Fire Alarm DC 9V Battery Back up En14604 220V Smoke Detector

• Type: Smoke Detectors
• Anti-theft Alarm System Approach: Active
• Anti-Theft Alarm System Type: Smoke Alarms
• Anti-Theft Alarm System-Wide: Wire Alarm Detectors
• Anti-Theft Alarm System Distance: Common Detectors
• Types of Smoke Detectors: Photoelectric Smoke Style
• Model NO.: TSS890B-HI
• Infrared Sensor Probe Type: Inclination Sensor
• Infrared Sensor Installation: Ceiling
• Power Source: AC220V-AC240V, DC 9V Battery Backup
• Size: 140mm in Diameter X 44mm Depth
• Certificate: CE, Bsi, Ukca, RoHS, Reach, ISO9001, BSCI
• Transport Package: Carton
• Specification: 140mm in diameter x 44.9mm depth
• Trademark: JBE
• Origin: Zhejiang, China
• Production Capacity: 100000 Piece/Month

Product Description

 

AC 220V main power DC 9V backup battery with wired 
interconnection photoelectric smoke alarm(wireless module optional)
 

Technical Specifications:

Power Source	AC 220V-AC240V, DC 9Vbattery backup	Alarm Volume	>85dB(A) @ 3 meters
AC Quiescent Current	< 100mA	Low Voltage Threshold	≤7.5V
AC Alarm Current	< 100mA	Hush Time	8minutes
DC Quiescent Current	< 10uA	Product Service Life	>10 years
DC Alarm Current	< 28mA	Humidity Range	< 93% relative humidity (RH)
Alarm Sensitivity	0.10-0.16dB/m	Temperature Range	0ºC to 40ºC
Comply With Standard	EN14604:2005/AC:2008	Size	140mm in diameter x 44.9mm depth
Sound Pattern	(BI 0.5s - pause 0.5s - BI 0.5s - pause 0.5s - BI 0.5s - pause 1.5s, with the RED LED flash, repeat this alarm pattern)

Details of the product function:

Standby mode	after the product is installed, if the smoke alarm device operate properly, the red LED flashes once every 40 seconds
Local alarming mode	when the smoke alarm device detect particles of combustion and the concentration of smoke reaches the alarm threshold, the red LED will flash once per second with pulsating alarm until the smoke is disappeared
Interconnection alarming mode	when the smoke alarm device detect particles of combustion and the concentration of smoke reaches the alarm threshold, the alarm will send local alarm signal, other interconnection alarms will send alarm signals. The wired interconnection alarms will go into interconnection alarm mode: BI - BI - pause 1.2s, with the red LED flashes, this alarm pattern is repeated
Low battery mode	when the battery voltage below threshold, the red LED will flash once every 40 seconds with a sound of "chrip"
Fault mode	if the alarm detection signal decays below threshold, the alarm chirp occurs without LED flashes every 40 seconds
Silence mode	press the test button at least 2 seconds, it will go into silence mode for approx 8 minutes. That will desensitize the alarm sensitivity temporarily. At this time, the red LED will flash once every 8 seconds
No disturb mode	when the alarm device is in low battery mode, in order to avoid disturbing you at night, please press the test button for 3 seconds which will mute this warning tone for about 14 hours. After 14 hours, the warning tone will still go off. The red LED will flash once every 40 seconds during No disturb mode
Test mode	test the unit to ensure proper operation by pressing the test button. At this time, the red LED will flash once per second with pulsating alarm until test button is released
NOTE	WEEKLY TESTINGIS REQUIRED.

Wireless Interconnection Set up:

>1<	Select one of smoke alarms as the MASTER unit. Treat other units as SLAVE units.
>2<	Press the test button on the MASTER unit three times within two seconds, the red LED will flash quickly, the unit is now in sending radio signal mode. This mode will last for 48 seconds.
>3<	While the MASTER unit is in sending radio signal mode, press the test button on any SLAVE unit three times within two seconds, the SLAVE unit learns this signal and completes the pairing after a sound "beep" with light flash once
>4<	Repeat the above steps on all other SLAVE units
Clear wireless connection function	Press the test button on any SLAVE unit three times within two seconds, the red LED will flash quickly, then press and hold the test button again until the red light goes out the first time and release the button immediately, the red LED will flash slowly, at this time, press the test button again, the SLAVE unit will beep 3 times, which means that the SLAVE unit clears wireless connected successfully.